innosferaНаука и инновацииScience and Innovations1818-98572412-9372Издательский дом «Белорусская наука»innosfera-627Research ArticleТЕМА НОМЕРА: НАНОТЕХНОЛОГИИТЕМА НОМЕРА: НАНОТЕХНОЛОГИИАддитивное производство металлических и керамических порошковых материаловAdditive manufacturing of metal and ceramic powder materialsИльющенкоА.IlyushchenkoA.

Александр Ильющенко, директор Института порошковой металлургии, генеральный директор ГНПО порошковой металлургии, академик, профессор

Alexander Ilyushchenko 

ТалакоТ.TalakoT.

Татьяна Талако, заместитель академика-секретаря, доктор технических наук, профессор

Tatyana Talako 

ЛецкоА.LetskoA.

Андрей Лецко, заведующий, кандидат технических наук, доцент

Andrey Letsko 

Институт порошковой металлургии; ГНПО порошковой металлургииBelarusОтделение физико-технических наукBelarusНИЛ №15Belarus202425072024062837Copyright © Издательский дом «Белорусская наука», 20242024Издательский дом «Белорусская наука»Издательский дом «Белорусская наука»https://innosfera.belnauka.by/jour/about/submissions#copyrightNoticehttps://innosfera.belnauka.by/jour/article/view/627

Показаны преимущества, ограничения и пути улучшения аддитивного производства металлических и керамических порошковых материалов, представлены основные этапы полного производственного цикла построения и основных параметров, определяющих структуру и свойства получаемых продуктов.

The article describes the advantages, limitations and ways to improve the additive production of metal and ceramic powder materials, the main stages of the complete production cycle construction and the main parameters determining the structure and properties of the products produced.

ReferencesИльющенко А.Ф. Аддитивные технологии и порошковая металлургия: монография / А.Ф. Ильющенко // Национальная академия наук Беларуси; Институт порошковой металлургии имени академика О.В. Романа. – Минск, 2019.Ильющенко А.Ф. Аддитивные технологии и порошковая металлургия: монография / А.Ф. Ильющенко // Национальная академия наук Беларуси; Институт порошковой металлургии имени академика О.В. Романа. – Минск, 2019.Dawes J. Introduction to the additive manufacturing powder metallurgy supply chain / J. Dawes, R. Bowerman, R. Trepleton // Johnson Matthey Technol. Rev. 2015. Vol. 59. No3. P. 243–256.Dawes J. Introduction to the additive manufacturing powder metallurgy supply chain / J. Dawes, R. Bowerman, R. Trepleton // Johnson Matthey Technol. Rev. 2015. Vol. 59. No3. P. 243–256.M. Heynick. Additive manufacturing of metals: a review // Proc. Of MS&T11, Additive Manufacturing of Metals. – Columbus, Oh. 2011. P. 1413–1425.M. Heynick. Additive manufacturing of metals: a review // Proc. Of MS&T11, Additive Manufacturing of Metals. – Columbus, Oh. 2011. P. 1413–1425.А.Ф. Ильющенко, А.И. Лецко, Т.Л. Талако // Порошковая металлургия: Респ. межвед. сб. науч. трудов. – Минск, 2017. Вып. 40. С. 48–53.А.Ф. Ильющенко, А.И. Лецко, Т.Л. Талако // Порошковая металлургия: Респ. межвед. сб. науч. трудов. – Минск, 2017. Вып. 40. С. 48–53.Introduction to additive manufacturing technology. A guide for designers and engineers // EPMA V2-REVISED. N12. 2012. P. 44.Introduction to additive manufacturing technology. A guide for designers and engineers // EPMA V2-REVISED. N12. 2012. P. 44.Optimum Part Build Orientation in Additive Manufacturing for Minimizing Part Errors and Support Structures / P. Das [et al.] // Procedia Manufacturing. 2015. N1. P. 343–354.Optimum Part Build Orientation in Additive Manufacturing for Minimizing Part Errors and Support Structures / P. Das [et al.] // Procedia Manufacturing. 2015. N1. P. 343–354.Gaynor A.T. Topology optimization considering overhang constraints: Eliminating sacrificial support material in additive manufacturing through design / A.T. Gaynor, J.K. Guest // Structural and Multidisciplinary Optimization. 2016. N54. P. 1157–1172.Gaynor A.T. Topology optimization considering overhang constraints: Eliminating sacrificial support material in additive manufacturing through design / A.T. Gaynor, J.K. Guest // Structural and Multidisciplinary Optimization. 2016. N54. P. 1157–1172.Additive manufacturing of metallic components – Process, structure and properties / T. DebRoy [et al.] // Progress in Materials Science Prog. 2018. N92. P. 112–224.Additive manufacturing of metallic components – Process, structure and properties / T. DebRoy [et al.] // Progress in Materials Science Prog. 2018. N92. P. 112–224.Рудской А.И. Аддитивные технологии. Материалы и технологические процессы: монография / А.И. Рудской [и др.]. – СПб., 2021.Рудской А.И. Аддитивные технологии. Материалы и технологические процессы: монография / А.И. Рудской [и др.]. – СПб., 2021.Defects and anomalies in powder bed fusion metal additive manufacturing / А. Mostafaei [et al.] // Current Opinion in Solid State and Materials Science. N26. 2022.Defects and anomalies in powder bed fusion metal additive manufacturing / А. Mostafaei [et al.] // Current Opinion in Solid State and Materials Science. N26. 2022.Metal Additive Manufacturing Cycle in Aerospace Industry: A Comprehensive Review / B. Barroqueiro [et al.] // Journal of Manufacturing and Materials Processing. 2019. N6.Metal Additive Manufacturing Cycle in Aerospace Industry: A Comprehensive Review / B. Barroqueiro [et al.] // Journal of Manufacturing and Materials Processing. 2019. N6.Singh S. Material issues in additive manufacturing: A review / S. Singh, S. Ramakrishna, R. Singh // Journal of Manufacturing Processes. – 2017. Vol. 25. P. 185–200.Singh S. Material issues in additive manufacturing: A review / S. Singh, S. Ramakrishna, R. Singh // Journal of Manufacturing Processes. – 2017. Vol. 25. P. 185–200.Diener S. Literature review: Methods for achieving high powder bed densities in ceramic powder bed based additive manufacturing / S. Diener, A. Zocca, J. Günster // Open Ceramics. 2021. N8. P.100191b.Diener S. Literature review: Methods for achieving high powder bed densities in ceramic powder bed based additive manufacturing / S. Diener, A. Zocca, J. Günster // Open Ceramics. 2021. N8. P.100191b.Direct laser sintering of a silica sand / Y. Tang [et al.] // Materials and Design. 2003. N24. P. 623–629.Direct laser sintering of a silica sand / Y. Tang [et al.] // Materials and Design. 2003. N24. P. 623–629.An investigation of rapid prototyping of sand casting molds by selective laser sintering / G. Casalino [et al.] // Journal of Laser Applications. 2002. N14. P. 100–106.An investigation of rapid prototyping of sand casting molds by selective laser sintering / G. Casalino [et al.] // Journal of Laser Applications. 2002. N14. P. 100–106.Ceramic components manufacturing by selective laser sintering / P. Bertrand [et al.] // Applied Surface Science. 2007. N254. P. 989–992.Ceramic components manufacturing by selective laser sintering / P. Bertrand [et al.] // Applied Surface Science. 2007. N254. P. 989–992.Sercombe T.B. Rapid manufacturing of aluminum components / T.B. Sercombe, G.B. Schaffer // Science 301 (2003) 1225–1227.Sercombe T.B. Rapid manufacturing of aluminum components / T.B. Sercombe, G.B. Schaffer // Science 301 (2003) 1225–1227.M. Geiger (Ed.). Laser Assisted Net Shape Engineering 2: Proceedings of the 30th International CIRP Seminar on Manufacturing Systems – LANE’97, Meisenbach, Bamberg, 1997. Erlangen, September 23–26.M. Geiger (Ed.). Laser Assisted Net Shape Engineering 2: Proceedings of the 30th International CIRP Seminar on Manufacturing Systems – LANE’97, Meisenbach, Bamberg, 1997. Erlangen, September 23–26.Materials for additive manufacturing. CIRP Annals / D. Bourell [et al.] // Manufacturing Technology. 2017.Materials for additive manufacturing. CIRP Annals / D. Bourell [et al.] // Manufacturing Technology. 2017.Electron beam sintering of ceramics for additive manufacturing / A.S. Klimov [et al.] // Vacuum. 2019. N169 P. 108933.Electron beam sintering of ceramics for additive manufacturing / A.S. Klimov [et al.] // Vacuum. 2019. N169 P. 108933.Development of a new calcium phosphate powder-binder system for the 3D printing of patient specific implants / A. Khalyfa [et al.] // Journal of Materials Science: Materials in Medicine. 2007. N18. P. 909–916.Development of a new calcium phosphate powder-binder system for the 3D printing of patient specific implants / A. Khalyfa [et al.] // Journal of Materials Science: Materials in Medicine. 2007. N18. P. 909–916.Microwave Sintered 3D Printed Tricalcium Phosphate Scaffolds for Bone Tissue Engineering / S. Tarafder [et al.] // Journal of Tissue Engineering and Regenerative Medicine. 2013. N7, 8. P. 631–641.Microwave Sintered 3D Printed Tricalcium Phosphate Scaffolds for Bone Tissue Engineering / S. Tarafder [et al.] // Journal of Tissue Engineering and Regenerative Medicine. 2013. N7, 8. P. 631–641.D.J. Thomas. 3-D printing of polymer-derived CMCs for next-generation turbine blade manufacture // American Ceramic Society Bulletin. 2017. N96. P. 28–30.D.J. Thomas. 3-D printing of polymer-derived CMCs for next-generation turbine blade manufacture // American Ceramic Society Bulletin. 2017. N96. P. 28–30.Short fiber reinforced 3D printed ceramic composite with shear induced alignment / D.E. Yunus [et al.] // Ceramics International. 2017. N43(15). P. 11766–11772.Short fiber reinforced 3D printed ceramic composite with shear induced alignment / D.E. Yunus [et al.] // Ceramics International. 2017. N43(15). P. 11766–11772.Diener S. Literature review: Methods for achieving high powder bed densities in ceramic powder bed based additive manufacturing / S. Diener, A. Zocca, J. Günster // Open Ceramics. 2021. N8. P. 100191b.Diener S. Literature review: Methods for achieving high powder bed densities in ceramic powder bed based additive manufacturing / S. Diener, A. Zocca, J. Günster // Open Ceramics. 2021. N8. P. 100191b.

The authors declare that there are no conflicts of interest present.